Cover of Copper: Ore, Wire, Power, a book by Ketineni RamaraoFrom the book Copper: Ore, Wire, Power
Chapters 15, 16, 17 and 24. Read the full book free as a PDF.

Concentrate arrives at the smelter as a dark, damp sand holding roughly a quarter copper, the rest sulphur, iron and stubborn rock. The smelter's job is to burn and slag away everything that is not copper, and it does so in stages, each hotter and more decisive than the last.

Matte: the first separation

In the furnace, the concentrate is melted with a flux, and the mixture splits by density and chemistry into two liquids. Iron oxide joins the flux as slag, a glassy waste that is skimmed off. Copper and sulphur sink together as matte, a molten sulphide carrying half to two-thirds copper. The oldest smelters did this in reverberatory furnaces, where flames washed over a shallow bath. Flash smelting is one major modern route, first run on an industrial scale on 20 April 1949 at Outokumpu's Harjavalta smelter in Finland: dried concentrate and oxygen-enriched air are blown down a reaction shaft, the sulphur ignites, and the ore effectively burns itself, cutting the electricity needed per tonne of copper to about a third of the old electric-furnace process.

A sepia 1865 photograph of a copper smelter with tall chimneys and industrial buildings in a mountain valley.
The copper smelter at Gedabey, Azerbaijan, photographed in 1865 by Siemens Corporate Archives. Nineteenth-century smelters moved the fire to the ore. Photo: Siemens Corporate Archives, Public domain, via Wikimedia Commons.

Why the smelter moved

The economics inverted as mines grew: concentrate is mostly waste, so it is cheaper to ship metal than rock, and much smelting moved nearer the mines, to Chile, Arizona and Zambia, while Japan built port smelters on imported concentrate and Wales kept the memory and little else. Where a smelter sits tells you who held the power in the trade: once the coal districts, now the orebodies.

Converting: driving out the sulphur

Matte then goes to the converter, where air is blown through the melt. The remaining iron slags off, the sulphur burns away as sulphur dioxide, and what is left is blister copper, about 98.5 percent metal, named for the gas bubbles that blister its surface as it solidifies. The sulphur dioxide is too valuable and too dangerous to vent: modern smelters capture it and turn it into sulphuric acid, so much of it that acid plants are a business in their own right.

Fire refining and the tankhouse

Blister copper gets a last cleaning in the anode furnace, air and then a reducing gas stripping the final oxygen, and is cast into anodes: flat plates of a few hundred kilograms with lugs for hanging. That is the end of fire. The last one percent, iron, arsenic, antimony, sulphur, and the precious metals that have ridden along since the ore, would wreck copper's conductivity, and removing it is work for electricity, not heat.

In the tankhouse, anodes hang in cells of warm, acidified copper sulphate solution, alternating with thin starter sheets of pure copper. A gentle current dissolves copper from the anode and plates it, atom by atom, onto the cathode. Over ten days or so the sheets grow into slabs of a hundred kilograms and more of 99.99 percent copper. The base metals dissolve and are bled away; the noble ones never dissolve at all. Gold, silver, platinum group metals, selenium and tellurium fall to the cell floor as anode slime, a residue so rich, tonne for tonne, that it is processed as a precious-metals ore in itself. The cathodes that emerge are the industry's standard product, assayed, stacked and sold, ready to be melted, cast and drawn into the wire that electrifies everything else.

Quick answers

What are the steps in copper smelting?

Concentrate is smelted to matte, converted to blister copper (about 98.5% pure), fire-refined and cast into anodes, then electrorefined in acid-copper-sulphate cells to 99.99% cathode. Sulphur dioxide off-gas is captured as sulphuric acid.

What is flash smelting?

Flash smelting blows dried concentrate with oxygen-enriched air down a reaction shaft so the sulphur ignites and the ore largely burns itself. First used industrially in 1949 at Harjavalta, Finland, it cut energy use to about a third of the older electric-furnace route.

What is the difference between matte, blister and cathode copper?

Matte is a molten copper sulphide at 50-70% copper, straight from the furnace. Blister copper is converted matte at about 98.5% purity. Cathode is electrorefined copper at 99.99%, the industry's standard commercial product.

Sources

Flash smelting date, location and energy figures from Metso's history of the process. Matte, converting, blister and tankhouse detail follow Chapters 15, 16 and 24 of the book.

More from this book

Process · From the book Copper: Ore, Wire, Power

How copper is extracted from ore

Copper ore is mostly not copper.

Materials · From the book Copper: Ore, Wire, Power

Why copper is used for electrical wiring

Copper is the standard metal for building wiring.

History · From the book Copper: Ore, Wire, Power

A history of copper: the first metal

Copper was humanity's first metal, and after ten thousand years it is still the one we cannot electrify without.