Impact · Consumer Discretionary · Textiles Apparel and Luxury Goods
The carbon footprint of a pair of sneakers: why the factory, not the fabric, dominates
People assume the footprint of a shoe is in its materials. One widely cited life-cycle study found the opposite: most of it comes from the energy used to make the parts and assemble the pair.
From the book The Sneaker: Rubber, Air, FoamChapter 13. Read the full book free as a PDF.
The number
A team led by Randolph Kirchain and Elsa Olivetti at MIT's Materials Systems Laboratory used life-cycle assessment under ISO 14040 and 14044 to estimate the footprint of a typical pair of synthetic running shoes. The result, published in the Journal of Cleaner Production in April 2013, was 14 kg of CO2-equivalent, plus or minus 2.7. MIT Technology Review translated that as about 30 pounds, which it likened to keeping a 100-watt bulb on for a week.
The abstract also cites two company estimates for running shoes of between 18 and 41 kg CO2-equivalent per pair (PUMA, 2008, and Timberland, 2009). So 14 kg is at the low end of the published range, and the spread tells you how much method and boundaries matter.
Where the carbon comes from
The study put about 29% of the impact in materials processing and about 68% in manufacturing. The authors point out this is unusual. For most consumer products that need no electricity in use, materials are the biggest share. Shoes are different because the parts are small and light but the processing is intense: the single shoe the MIT-led study analysed had 65 discrete parts and more than 360 processing steps, including cutting, sewing, injection moulding, foaming and heating. The factory sequence is described in how sneakers are made.
The other driver is the electricity grid. MIT Technology Review reports that much of the carbon impact comes from powering the plants, because a significant share of shoe makers are in China, where coal is the dominant source of electricity. The same footprint made in a plant on a cleaner grid would be lower. The study frames this as a place to act: the researchers say that material swaps alone may not be enough when manufacturing energy is the larger term.
What the brands say now
adidas's 2024 annual report states that greenhouse gas emissions from manufacturing are a major contributor to its CO2e emissions. It says it works with suppliers on decarbonisation targets, including renewable energy and more sustainable materials, aligned with the Science Based Targets initiative, and rewards suppliers for performance through product allocation. It gives no per-pair figure in the section reviewed. That is the same conclusion as the 2013 study, reached from inside the industry.
There is a link to where the factories are. Because most branded sneakers come from three Asian countries, the carbon intensity of those national grids sets much of the footprint, and brands depend on their suppliers to change it.
What this study cannot tell you
- It is one "typical" synthetic running shoe, modelled in 2012-13. It is not your shoe and not today's average.
- The percentages come from the abstract. The remaining few percent, such as transport, use and disposal, are not itemised in the source reviewed, so none are claimed here.
- No source reviewed gives a verified sneaker recycling or repair rate, so end-of-life is left out.
The materialist reading
A sneaker is a small amount of oil-derived material turned into a complicated object with many heat-and-glue steps. The footprint follows the steps. The lever is the grid, and the design choice that matters is fewer parts and fewer steps, which is part of why knitted uppers and moulded midsoles keep spreading. Whether they cut the footprint is a claim that needs a life-cycle study of its own, and none was found.
Quick answers
What is the carbon footprint of a pair of sneakers?
An MIT-led 2013 study estimated 14 kg of CO2-equivalent (plus or minus 2.7) for a typical pair of synthetic running shoes. Company estimates cited in the same paper range from 18 to 41 kg.
What part of a sneaker's footprint is manufacturing?
About 68% in the MIT-led study, with about 29% from materials processing.
Why is manufacturing so carbon-heavy for shoes?
The single shoe the MIT-led study analysed had 65 parts and more than 360 processing steps, and a lot of the energy comes from electricity in countries where coal is dominant, according to MIT Technology Review.
Are sneakers recyclable?
No verified sneaker recycling or repair rate was found in the sources reviewed, so this article makes no claim.
