Cover of The Pneumatic Tire: Air, Rubber, Road, a book by Ketineni RamaraoFrom the book The Pneumatic Tire: Air, Rubber, Road
Chapters 8, 9 and 10. Read the full book free as a PDF.

The air carries the load

Inflation pressure, not rubber stiffness, supports the weight. A car tire at two and a half bar presses its contact patch flat against the road until the patch area times the pressure equals the load on that corner - a few square decimetres of rubber, about the size of a hand, doing the holding. This is why underinflation is dangerous: a soft tire flexes its sidewalls too far on every revolution, the flexing becomes heat, and heat destroys the structure from inside. It is also why the tire was a revolution at all. A solid rubber or iron-shod wheel carries the load through its own material and transmits every bump; the pneumatic tire carries it on a column of air and absorbs the bumps in the same motion. Dunlop's tricycle experiment of 1888 was, physically, the substitution of a spring of air for a spring of wood.

Cutaway diagram of a radial tire showing the tread, steel belts, carcass ply, bead, sidewall and innerliner, with an arrow marking the contact patch where air pressure carries the load.
What is inside: the layers of a radial tire. The air carries the load; the casing gives it shape. Original IOI diagram.

The casing: a cord skeleton in a rubber skin

What keeps the air shaped is the carcass - a fabric of cord laid into rubber, running from bead to bead. The beads, hoops of steel wire, clamp the tire to the rim and transmit every force between wheel and casing. Around the casing sit the working parts: an airtight innerliner in place of a tube, sidewalls that flex, belts that brace the tread, and the tread itself. The British Tyre Manufacturers' Association lists what that adds up to materially - about 42 percent elastomers, 28 percent carbon black and silica, 12 percent steel, 5 percent textile - a composite that no single material could replace. The tread's grooves are not decoration: they are channels that pump water out of the contact patch so rubber can meet road instead of skating on a film.

Bias to radial: the 1946 redesign

For sixty years tire cords crossed diagonally, layer over layer - the bias-ply tire - and the construction's flaws were known: the crossed plies scissored against each other as the tire rolled, building heat in the sidewall and limiting life. On 4 June 1946 Michelin registered the patent that rearranged the architecture: carcass cords running radially, straight from bead to bead at right angles to the direction of travel, with a stiff steel belt bracing the tread. Michelin's own account credits engineer Marius Mignol, and records the prototype's nickname - the "fly trap" - for the strange looks of its soft, bulging sidewall. The radial ran cooler, gripped better, rolled easier and lasted longer; the MICHELIN X swept Europe through the 1960s. America resisted - its makers answered with the belted-bias compromise - until Goodyear, the largest holdout, announced steel-belted radial lines in December 1972. Firestone's radial setbacks, in Harvard Business School's account of the episode, ended in the company's 1988 sale to Bridgestone. The construction Dunlop industrialized was bias; the construction the world drives on is Michelin's rearrangement of it.

Tubeless: sealing the air to the rim

Dunlop's tire was a tube inside a casing, and a punctured tube deflated at once. The tubeless tire - airtight liner inside the casing, bead sealed against a shaped rim - can lose air more slowly after some punctures and can survive nails that would have stranded a tubed wheel, though a large puncture can still deflate it quickly. The idea had a long gestation: Killen Tire took a British patent in 1928, granted 1930; Goodyear filed its Wingfoot design in South Africa in 1944; Frank Herzegh applied in the United States in 1946 and received US patent 2,587,470 in 1952 - butyl rubber, the nearly impermeable synthetic, was the enabling material. B.F. Goodrich announced its tubeless tire on 11 May 1947 after more than three years of engineering and taxi and police fleet tests; the New York Times reported in December 1954 that tubeless tires gave "at least 25 per cent more mileage" with "almost no blowouts." Tubeless tires became standard on many new American cars during the 1950s.

Reading the sidewall, and regulating the wear

The sidewall is a datasheet. The Tire Industry Association's decoder reads P225/60R16 97V as: passenger tire, 225 millimetres wide, sidewall height 60 percent of width, radial construction, 16-inch rim, load index 97, speed rating V - with a DOT code and tire identification number tracing plant and production week. And the newest lines on the tire's record are regulatory: because the whole mechanism works by abrading rubber against road, the EU's Euro 7 regulation (2024/1257) extends vehicle rules to tire particles for the first time, with a phased timetable that distinguishes C1, C2 and C3 tires and new type approvals from all new tires - tire wear being estimated as the largest single source of microplastics released into the environment. The air still carries the load; what the air leaves behind is now the industry's next design problem.

Quick answers

What actually holds the car up - the rubber or the air?

The air. Inflation pressure carries the load; the contact patch flattens until its area times the pressure equals the corner's weight. The casing is there to contain and shape the air and to give the tire grip and structure.

What is the difference between bias-ply and radial tires?

The direction of the carcass cords. Bias-ply cords cross diagonally in layers, which flex and scissor as the tire rolls, building heat. Radial cords run straight from bead to bead under a stiff belt, so the sidewall flexes without fighting the tread - cooler running, longer life, better grip. Michelin patented the design in 1946.

When did tires stop having inner tubes?

After the Second World War. The patents run from 1928 (Killen, Britain) through B.F. Goodrich's May 1947 announcement, with butyl rubber as the enabling material. During the 1950s tubeless tires became standard on many new American cars.

Sources

Radial patent date and prototype details are from Michelin's own history pages. The 1972 Goodyear announcement and Firestone's radial difficulties are from the New York Times via Harvard Business School Working Knowledge. Sidewall decoding follows the Tire Industry Association.

More from this book

History · From the book The Pneumatic Tire: Air, Rubber, Road

Who invented the pneumatic tire?

The pneumatic tire was invented twice.

Materials · From the book The Pneumatic Tire: Air, Rubber, Road

What are tires made of?

Ask a tire maker what a tire is made of and the honest answer is a list of more than a hundred raw materials.

Process · From the book The Pneumatic Tire: Air, Rubber, Road

How are tires made? Mixing, building and curing a modern tire

A tire arrives at the factory as a hundred raw materials and leaves as a single object that cannot be taken apart.