Process · Consumer Discretionary · Automobile Components
How are tires made? Mixing, building and curing a modern tire
A tire arrives at the factory as a hundred raw materials and leaves as a single object that cannot be taken apart. The transformation happens in three acts - mixing the rubber compounds, building the tire layer by layer on a drum, and curing it under heat and pressure - and the middle act is still closer to tailoring than to assembly.
From the book The Pneumatic Tire: Air, Rubber, RoadChapters 5 and 9. Read the full book free as a PDF.
Mixing: the Banbury kitchen
Tire making begins as cookery at industrial scale. Goodyear's own description of the process counts about 30 different rubber compounds in a modern tire, each a separate recipe of natural and synthetic rubber, carbon black or silica, oils, sulphur, accelerators and protective waxes. The recipes are combined in Banbury mixers - sealed chambers with counter-rotating rotors that knead tonnes of rubber the way a baker kneads dough, only hotter and under precise temperature control, because mix too hot and the compound begins to cure in the machine. The ILO's occupational encyclopaedia notes that a single plant keeps hundreds of component specifications in production, and that mixing is the plant's heaviest exposure point: fine carbon black dust and chemical vapours are why the room is ventilated like a smelter. Each compound is mixed for a purpose - a soft airtight innerliner, a hard bead filler, a tread tuned for grip or wear.
Components: an engineered composite, piece by piece
Mixed rubber is then formed into the tire's parts. Extruders squeeze tread and sidewall rubber through shaped dies into continuous ribbons. Calenders press rubber onto sheets of textile or steel cord, making fabric that is rubber and fibre in one skin. Brass-coated steel wire is drawn, spun into bead hoops and woven into belt fabric. A radial passenger tire carries a bead at each rim seat, a carcass ply of polyester or rayon cord running bead to bead, two steel belts under the tread, a nylon cap ply, sidewalls, an airtight innerliner of butyl rubber, and the tread itself - roughly a dozen engineered components, each with its own material.
Building: the green tire
Assembly happens on a rotating drum, and it is the industry's craft stage. The innerliner goes on first, then the carcass plies, then the bead rings are set and the ply ends folded over them; a second drum adds belts and tread; the two halves are married and the flat cylinder is inflated into a torus. The result is called a green tire - green as in uncured, not environmental: sticky, pale, treadless-looking, with the geometry of a tire but none of its properties. Highly automated plants build a green tire in under a minute, but the motion is still a tailor's - layers laid, wrapped and stitched by pressure rollers.
Curing: the mold that makes it one thing
Curing is the transformation. The green tire is loaded into a segmented mold, a rubber bladder inflates inside it to press it against the mold walls, and heat does the chemistry: Goodyear describes curing at over 300 degrees Fahrenheit for 12 to 25 minutes depending on tire size. The mold engraves the tread pattern and the sidewall markings while vulcanization - Goodyear's 1839 reaction, sulphur bridges linking the rubber chains - locks the composite into a single elastic solid. What goes in is an assembly of tapes and sheets that could be peeled apart; what comes out cannot be. Inspection follows: visual checks, X-ray and uniformity machines that spin the tire and measure force variation, because a tire is a safety component spinning at highway speed and every one is tested as such.
Why the factory still has hands in it
For all the automation, tire building resisted full mechanisation longer than almost any mass-production process, because the material is alive in a way sheet steel is not: rubber creeps, sticks and remembers, and every layer must be placed to a tolerance while it is still soft enough to move. The Banbury room, the calendar line and the curing press are heavy industry; the building drum is closer to a workbench. The ILO entry treats the whole plant as an occupational-health environment - dust in mixing, solvents in cementing, heat at the presses - which is itself a measure of how much of the process happens within arm's reach of a person.
The scale of the industry
The process repeats, worldwide, on a scale few manufactured goods match. Smithers estimates the global tire market at $282 billion and about 2.6 billion tires in 2025, forecasting $367 billion and 3.1 billion units by 2030. MarketLine's broader market definition counts 2,317 million tires and $365.4 billion of revenue for 2024 - the two houses scope the market differently, and the book presents both rather than splitting the difference. Concentration is high at the top: Tyrepress's 2025 ranking of FY2024 sales puts Michelin at 27.19 billion euros and Bridgestone at 27.17 billion, with Goodyear at 18.17 billion; Michelin alone reports 69 production facilities and 114,000 employees. Every one of those factories runs the same three-act play - mix, build, cure - that Firestone was demonstrating at the 1939 World's Fair, automated now but recognisably the same transformation of a hundred materials into one elastic machine part.
Quick answers
What is a "green" tire?
An uncured one. After the layers are assembled on the building drum, the tire is sticky, soft and shapeless in performance terms - "green" as in unripe. Curing in the hot mold vulcanizes the rubber and turns the assembly into a single solid piece.
How long does it take to make a tire?
The building stage is under a minute in a modern automated plant; curing takes 12 to 25 minutes per tire depending on size, per Goodyear's process description. Mixing, component preparation and inspection surround those two steps.
Why can't a tire be disassembled for recycling?
Because curing made it one object. Vulcanization cross-links the rubber permanently, and the process bonds rubber, steel and textile into a single composite. That chemical permanence is exactly what makes end-of-life tires a hard problem.
Sources
- Goodyear, "How Tires Are Built" (archived via the Internet Archive Wayback Machine)
- ILO Encyclopaedia of Occupational Health and Safety, "Tools, Equipment and Materials" (rubber/tyre manufacturing entry)
- Smithers, "Market Outlook for Global Tires" (The Future of Global Tires to 2030 infographic)
- MarketLine Global Tires & Rubber profile summary, via Dream Incubator
- Tyrepress, "Leading tyre manufacturers" (2025 ranking, FY2024 sales)
- Michelin Guide, "The MICHELIN Company"
