Cover of The Ball Bearing: A perfect sphere, and the age of rotation it made possible, a book by Ketineni RamaraoFrom the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible
Chapters 58, 62, 63 and 64. Read the full book free as a PDF.

The four parts you can see

The inner ring fits the shaft and carries a ground groove, the raceway, on its outer surface. The outer ring sits in the housing and carries the matching raceway inside. The balls roll between them, turning a sliding interface into a rolling one. And the cage spaces the balls so they never rub: uncaged balls touch at twice the running speed, wearing and heating, which is why a cage of some kind appears as far back as Galileo's description of a caged bearing around 1600. This whole arrangement was patented in essentially its modern form by Philip Vaughan of Carmarthen in 1794, for iron balls running in grooved carriage-wheel axles, sealed in with a stopper.

Numbered cutaway diagram of a ball bearing showing inner ring, outer ring, balls and cage
The anatomy of a ball bearing: outer ring, inner ring, balls and cage. Photo: Niabot, CC BY-SA 3.0, via Wikimedia Commons.

The fifth part is a film

The most important component is not made of steel. At operating speed, each ball drags lubricant into its contact with the raceway, and under the immense pressure of the contact the oil momentarily stiffens into something like glass. That glassy film, a fraction of a micron thick, is what the load actually rests on. When the film is right, the steel surfaces never touch, and a bearing can run for decades. When it fails, through starvation, contamination or the wrong grease, metal meets metal and the clock starts.

The busiest square millimetre in engineering

In principle a sphere touches a groove at a point, which would mean infinite pressure. In practice the ball flattens slightly and the race yields, as a tyre flattens on the road, so the load sits on a small ellipse. Heinrich Hertz worked out the mathematics of that contact in the 1880s, and his equations still sit under every bearing rating published today. Even perfect rolling is not pure: different parts of the flattened ball move at slightly different speeds across the ellipse, so there is always some microscopic sliding. A ball bearing is not a frictionless device; it is a device that traded gross sliding for microscopic slip. And the load is not shared politely: in a radial bearing under load, fewer than half the balls carry a significant share at any instant, and the load cycles around the ring as it turns. That is why fatigue, not wear, sets the bearing's rated life.

Sealed, greased and forgotten

Most ball bearings sold today will never be touched by a maintenance engineer. They are filled at the factory with a grease chosen for the duty, at around a quarter to a third of the free space, and closed behind a steel shield or a rubber seal. A shield keeps dirt out and grease in without touching anything, so it adds no friction; a contact seal excludes water and fine dust almost completely at the price of drag. The sealed-and-greased bearing turned lubrication from a daily chore into a factory decision, and it is why the appliance, the car wheel and the motor can be assembled and forgotten. SKF markets hybrid ceramic bearings whose grease life runs up to eight times longer, a measure of how central the grease has become to the product.

How long it lasts

The catalogue rating life, the L10, is a statistical floor: the life that ninety percent of a large group of identical bearings will exceed. Most bearings in service outlive it many times over. The ones that die young almost always die of something the rating does not model: contamination denting the raceway, poor lubrication switching the film off, misalignment loading the raceway edge, or, increasingly, electricity. Inverter-driven motors send stray shaft currents arcing across the oil film, etching the raceway into a washboard pattern called fluting; SKF reproduced exactly this damage in its 2024 laboratory study of electric-vehicle bearings. A failed bearing is therefore read, not scrapped: the raceway keeps a written record of how it died.

Where the design came from

A Michaux velocipede, the bicycle type that created the first mass market for ball bearings
A Michaux velocipede. The bicycle boom made the ball bearing a mass product and pulled precision ball grinding into being. Photo: tetedelacourse, CC BY-SA 2.0, via Wikimedia Commons.

The arrangement proved itself in public early. In November 1869 James Moore won the Paris-Rouen road race, counted as the world's first bicycle race, on a machine fitted with Jules Suriray's patented ball bearings. Over a hundred kilometres of bad French road, rolling beat grinding on the result sheet, and the bicycle boom that followed created the first mass demand for precision bearings in history. The demand then pulled into being the supply the idea had waited centuries for, told in how bearing balls are made.

Quick answers

Do the balls touch the raceways?

Not while the lubricant film is healthy. At speed, each ball rides on a pressurised film of oil or grease a fraction of a micron thick; the steel surfaces are fully separated. Wear begins when the film fails.

Why do ball bearings have a cage?

Without a cage, adjacent balls rub against each other at twice the running speed, generating heat and wear. The cage spaces the balls so each one rolls freely.

What kills a ball bearing early?

The field-failure list is consistent: contamination in the lubricant, poor or wrong lubrication, misalignment, mounting damage, moisture, and, in modern inverter-driven motors, electrical current arcing through the bearing and fluting the raceways.

Sources

The four-parts-and-a-film framing follows Chapters 58 and 69 of the book. Lubricant-film physics and load sharing per the rolling-element bearing literature; L10 conventions per the bearing life literature cited in the book's source companion.

More from this book

Manufacturing · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

How bearing balls are made

A ball bearing is only as good as its worst ball.

Manufacturing · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

How ball bearings are manufactured

A ball bearing is a promise expressed in microns, and the promise is kept by process: form, harden, grind, finish, under constant gauging.

Guide · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

Types of rolling bearings

The ball bearing is not one object but a family, each member a different answer to a single question: from which direction does the load come? Around the family sit the roller cousins and the rivals that beat any rolling element on one axis.