Guide · Industrials · Machinery
Types of rolling bearings
The ball bearing is not one object but a family, each member a different answer to a single question: from which direction does the load come? Around the family sit the roller cousins and the rivals that beat any rolling element on one axis.
From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possibleChapters 59, 67 and 68. Read the full book free as a PDF.
The deep groove: the default machine part of the world
The deep groove ball bearing takes radial loads, moderate axial loads in both directions, runs fast and quiet, and commonly arrives sealed and greased for life (shielded or open versions also exist). It is so dominant that when someone says "a bearing" without qualification, this is what they mean.

The specialists inside the family
The angular contact bearing shifts its raceways so the contact line runs at an angle, carrying combined radial and one-direction axial load; paired, it becomes the bearing of machine-tool spindles, about 19 percent of the market on GMI's figures. The self-aligning bearing, Sven Wingquist's 1907 invention born of a Gothenburg textile mill built on settling clay, grinds the outer raceway as a section of a sphere so the inner ring and balls swivel to follow a bent shaft: light loads, total forgiveness. The thrust ball bearing, the design Leonardo drew and the Roman emperor Caligula's lake ships arguably embodied, takes pure axial load at modest speed. At the edges sit four-point-contact bearings and the miniature world: MinebeaMitsumi's 1.5-millimetre bearing holds a Guinness record, and the firm claims over sixty percent of the miniature and small-sized segment below 22 millimetres.
The roller cousins
Five main types of rolling element share the industry's firms, markets and science. Balls touch at a point. Cylindrical rollers touch along a line and carry heavy radial loads at speed. Tapered rollers, Henry Timken's 1898 patent, carry combined loads and rule the wheel ends of heavy vehicles. Spherical rollers forgive misalignment under brutal loads. Needles pack load capacity into the thinnest possible cross-section; Georg Schaeffler's needle cage, developed in 1949, which guided each needle individually, made the needle bearing compact enough to conquer the automotive gearbox. Each is an industry in miniature, with its own machines, applications and specialists.
Point against line
Every catalogue offers the same choice in two forms, and everything in the trade-off follows from geometry. A ball's point contact carries less load but slips less, runs cooler at speed and forgives small misalignments. A roller's line contact spreads load over more steel, carries more, and pays in friction, heat and a lower speed ceiling. The partition is ancient: the Romans moved their heaviest column drums as rollers and their finest rotating platforms on balls. Two thousand years later the catalogues make the same assignment: the ball takes the motor, the spindle and the dental drill; the roller takes the rolling mill, the wind turbine main shaft and the freight wagon axle.
The rival that chooses neither
The plain or journal bearing uses no rolling elements at all. The rotating shaft drags oil into a converging wedge and climbs up onto it, aquaplaning in slow motion on a film measured in tens of microns. For the largest and slowest jobs, ship propeller shafts, hydroelectric turbines, the alternators of power stations, that film carries more than any reasonable arrangement of rolling elements, and with nothing rolling there is no rolling-contact fatigue. Rolling bearings took the jobs where starting friction matters, lubrication must be minimal or sealed for life, shaft position must be held to microns, and maintenance access is expensive. The boundary, drawn by load, speed, shock, cost and access, is one of the more quietly rational boundaries in engineering.
The exotics
Beyond the family sit the specialists that beat any rolling element on a single axis. Air bearings run the spindles of coordinate-measuring machines, the very instruments used to inspect bearings. Sapphire jewels run watch balances. Magnetic bearings suspend shafts with no contact at all; they have their own article, air and magnetic bearings. The ball bearing's genius is not to be best at anything. It is to be good at everything at once: the engineering references call it the best trade-off between cost, size, weight, capacity, durability, accuracy and friction, and to be manufacturable by the billion.
Quick answers
What is the most common type of bearing?
The deep groove ball bearing. It handles radial and moderate axial loads, runs fast and quiet, is commonly sealed and greased for life, though open and shielded versions exist.
What is the difference between a ball bearing and a roller bearing?
Contact geometry. A ball touches its raceway at a point, so it carries less load but runs faster, cooler and with less friction. A roller touches along a line, spreading the load over more steel to carry more, at the price of friction and a lower speed limit.
What is a self-aligning ball bearing?
A bearing whose outer raceway is ground as part of a sphere, so the inner ring and balls can swivel to follow a misaligned shaft. Sven Wingquist patented the multi-row design in 1907 and founded SKF around it.
Sources
- Global Market Insights, "Ball Bearing Market" (report GMI8015, 2026 edition)
- Wikipedia, "Ball bearing"
- Wikipedia, "Rolling-element bearing"
- Wikipedia, "Sven Wingquist"
- Tekniska museet, "Sven Wingquist - Spherical ball bearings"
- MinebeaMitsumi, "Minebea's 1.5 mm bearing" press release (2015)
- Wikipedia, "Journal bearing"
- Wikipedia, "Magnetic bearing"
- Schaeffler, 70 years of Schaeffler
