Cover of The Ball Bearing: A perfect sphere, and the age of rotation it made possible, a book by Ketineni RamaraoFrom the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible
Chapters 159 and 160. Read the full book free as a PDF.

Air: the stiffest thin film

An air bearing replaces the oil film with a film of pressurised gas. No contact means no wear, no lubricant and no contamination, and the errors of the surfaces average out across the film, so motion can be smoother than the parts that make it. The catch is capacity: air is much less viscous than oil, and load capacity depends on pad area and supply pressure, so air bearings are used where extreme precision matters more than load. Their signature job is telling: they run the spindles of coordinate-measuring machines, the instruments used to inspect the roundness of ball bearings. The referee of the bearing world rides on air.

Fluid: the one that got away

For decades the miniature ball bearing's most prestigious job was the spindle of the computer hard disk drive, spinning platters at thousands of revolutions with read heads floating nanometres above. Then the ball bearing lost the job. Modern drives spin on fluid dynamic bearings, a plain-bearing cousin in which a spiral-grooved journal self-pressurises an oil film, reducing noise and non-repeatable runout relative to conventional ball-bearing spindles. Below a certain vibration threshold, rolling contact itself becomes the noise. The episode keeps the industry's story honest: the ball bearing's empire is vast but not total, and its boundaries are drawn exactly where the finite sliding inside its contact ellipse becomes the application's binding constraint.

Magnetic: levitation with a control loop

The magnetic bearing abolishes contact entirely. Electromagnets arranged around the shaft hold it suspended while position sensors feed a controller that corrects the field thousands of times a second: no contact wear and no lubricant in the bearing itself, though machines keep a backup bearing for shutdowns and faults. The pedigree is older than the futuristic image. Jesse Beams at the University of Virginia filed a magnetic-suspension patent in December 1938 (granted in 1941) that used mechanical, electro-optical, electrical and hydraulic control, not digital; the technology matured with solid-state power electronics and digital control in the 1970s, and the French company S2M, founded in 1976, commercialised active magnetic bearings, with a pump application in 1976 and a compressor in 1985, according to SKF. The first big industrial home was natural gas: between 1996 and 2006 the Dutch producer NAM installed twenty compressors, each driven by a 23-megawatt motor on fully active magnetic bearings at the Groningen gas field, oil-free machines that could sit outdoors without a compressor house. SKF later bought the Revolve digital-control spin-out, which is how the ball bearing's founding house came to own a magnetic bearing line.

Cross-section diagram of an active magnetic bearing: shaft levitated between electromagnets with position sensors and a backup ball bearing
An active magnetic bearing. Sensors watch the shaft, electromagnets correct it thousands of times a second, and a backup bearing usually stands by in case the power fails. Diagram: IOI.

How the loop works

The magnetic bearing's bargain is explicit: it trades the ball's elegant passivity for electronics. Position sensors watch the shaft's location; a controller compares it with the setpoint and drives current into opposing electromagnets to pull the shaft back, thousands of times per second, in five axes at once. The rotor floats because software insists on it. Solid-state power electronics and digital control later widened the practical uses of active magnetic bearings. Hydrostatic and hybrid systems fill the middle ground, oil under pressure for the heaviest slow shafts, air for the lightest fast ones.

Where levitation earns its keep

The beachheads are exactly where contact is the problem. Turbomolecular pumps in semiconductor fabs, where a wear particle is a defect. Flywheel energy stores, where friction is a standing loss. Utility watt-hour meters. And most remarkably the magnetically suspended blood pumps of ventricular assist devices, where eliminating contact surfaces reduces blood damage and clotting: a bearing decision that a patient's survival can turn on.

The catch: a backup bearing stands by

Two caveats keep the ball bearing safe. Machines with magnetic bearings usually keep a mechanical backup, often a precision ball bearing or a bushing, for the moment power or control fails; the most advanced bearing in the machine is guarded by the oldest. And cost, weight and control complexity confine levitation to machines that justify it. A magnetic bearing trades the ball's elegant passivity for electronics and control loops, and most shafts on Earth will never repay the trade. The future of rotation is not balls versus magnets. It is balls, magnets, films and fields, each where it earns its keep, with the ball bearing, characteristically, standing by to catch the others when they fall.

Quick answers

Do magnetic bearings ever touch the shaft?

No. Sensors and electromagnets hold the shaft centred with no contact. But machines with magnetic bearings usually carry a mechanical backup bearing, often a precision ball bearing, to catch the shaft if power or control fails.

Where are air bearings used?

Wherever light loads must move with extreme smoothness: coordinate-measuring machine spindles, precision stages and similar instruments. Air films carry little load but average out surface errors, giving motion smoother than the parts themselves.

Why did hard disk drives stop using ball bearings?

Fluid dynamic bearings reduce noise and non-repeatable runout relative to conventional ball-bearing spindles. At the vibration levels a nanometre-scale read head demands, the residual sliding inside a ball bearing's contact became audible to the drive.

Sources

Magnetic-bearing history, the Groningen installation and applications per the magnetic bearing literature as cited in the book.

More from this book

Guide · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

Types of rolling bearings

The ball bearing is not one object but a family, each member a different answer to a single question: from which direction does the load come? Around the family sit the roller cousins and the rivals that beat any rolling element on one axis.

Mechanism · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

How ball bearings work

Open a ball bearing and you find four solid components and one invisible one.

Manufacturing · From the book The Ball Bearing: A perfect sphere, and the age of rotation it made possible

How bearing balls are made

A ball bearing is only as good as its worst ball.