Cover of Glass: Sand, Fire, Light, a book by Ketineni RamaraoFrom the book Glass: Sand, Fire, Light
Chapters 3, 27 and 35. Read the full book free as a PDF.

Step 1: the batch

Every ordinary window, bottle and drinking glass starts as a weighed mix called the batch. The base is silica sand, usually around three quarters of the mix. Soda ash makes it melt at a workable temperature, and limestone keeps the finished glass from dissolving in water. A modern batch also holds a few percent of helpers such as magnesia and alumina, and a large share of cullet, which is crushed glass from earlier production or from recycling.

The batch is computer-weighed, mixed dry and fed into the furnace at one end. The reason for each ingredient has its own article: why glass is made from silica sand, soda and lime.

A wide sand pit in Norfolk, England, with pale exposed sand, pools of standing water and a green grassy bank in the foreground.
A silica sand excavation at Leziate, Norfolk, England, 2010. Glass begins as ordinary-looking quarry sand, but it must be high in silica and low in iron. Photo: Richard Humphrey, CC BY-SA 2.0, via Geograph and Wikimedia Commons.

Step 2: the melt

The batch goes into a tank furnace, a refractory-lined pool of molten glass. Flames of gas or oil, or electric heating, hold the glass at roughly 1,500 to 1,600 degrees Celsius for container glass, according to glassmakers' own descriptions. Heat from the exhaust is recovered and used to preheat the incoming air, which is how the furnace keeps its fuel bill under control.

The furnace cannot be switched off. A tank full of cooling glass would freeze solid and wreck the structure, so a furnace is kept hot and running continuously. That fact shapes the economics of glass: you either run full, all day, every day, or you do not make glass.

Looking into the opening of a glass furnace: a bright orange and yellow pool of molten glass glowing against a dark interior.
Archive photograph, June 1972: inside a glass furnace where crushed bottles are made into molten glass. Photo: Bill Gillette, U.S. National Archives (EPA Documerica), Public domain, via Wikimedia Commons.

Step 3: refining

When sand, soda ash and limestone react, they release carbon dioxide, and the melt fills with bubbles. A bubble in a window is a flaw, so the glass moves slowly through the furnace into a refining zone, where it is held hot enough and long enough for the bubbles to rise out, helped by a small amount of a refining agent. It then drifts into a cooler conditioning zone where the temperature evens out, so that the glass leaving the furnace is the same everywhere.

Step 4: forming

Here the path splits, because glass is shaped differently depending on what it will become.

Step 5: annealing

Glass that cools unevenly traps stress inside, and stressed glass can crack hours or years later. So every finished product goes through an annealing oven, called a lehr. It carries the glass on rollers or a belt and cools it on a set schedule so that the whole thickness passes through its strain range together. This is the oldest lesson in glassmaking, cool it slowly, built into a tunnel of instrumented ovens.

Step 6: inspection and the return loop

At the cold end, cameras and lasers look for bubbles, stones, scratches and thickness errors. Glass that fails is crushed on the spot and goes straight back to the batch as cullet, which melts more easily than raw material because the chemistry has already happened once. Nothing is wasted except the energy already spent, and that is why the energy bill, more than the sand, decides where glass is made.

Diagram of the six steps of glass making: batch, melt, refine, form, anneal and inspect, with rejected glass returning to the batch as cullet.
The glass-making sequence. Original IOI diagram.

What sets the cost

Sand, soda ash and limestone are cheap per tonne. Heat is not. Melting is the most expensive step, so the industry works on getting more cullet into the batch, recovering more heat from exhaust gases and, where grids allow, adding electricity to the melt. The raw materials are a geology question and the furnace is an energy question, and a glass plant has to answer both at once.

Quick answers

Can you make glass from ordinary beach sand?

In principle yes, but the glass would come out coloured and uneven. Glassmaking needs sand that is high in silica and very low in iron, because iron turns glass green. Most beach and desert sand does not meet that.

How hot does a glass furnace get?

Container glassmakers describe melting at roughly 1,500 to 1,600 degrees Celsius.

Why do glass furnaces never stop?

A furnace holds hundreds or thousands of tonnes of molten glass. If it cooled, the glass would solidify and damage the refractory lining, so it runs continuously until it is due for a rebuild.

Go deeper in the book: Glass: Sand, Fire, Light · PDF · Source Companion

Sources

The 1,500-1,600 C melt range is from Toyo Glass. Furnace size and run length are not quantified.

More about glass

Ingredients · From the book Glass

Why glass is made from silica sand, soda and lime

Almost every window, bottle and drinking glass in the world is the same three-part recipe.

Process · From the book Glass

How float glass is made

Nearly every flat pane you look through was made by letting molten glass spread out on molten tin.

Recycling · From the book Glass

How glass is recycled

Glass can be melted and formed again without losing quality, so a bottle can be a bottle again indefinitely.