Cover of Crude Oil: Rock, Fuel, Empire, a book by Ketineni RamaraoFrom the book Crude Oil: Rock, Fuel, Empire
Chapters 12 to 16. Read the full book free as a PDF.

Modern wells are drilled by rotation. A bit studded with industrial diamonds or tungsten carbide teeth grinds away at the bottom of the hole, turned from the surface by the drill string, a kilometres-long screw of steel pipe assembled thirty metres at a time on the rig floor. Down the inside of the pipe the rig pumps drilling mud, an engineered fluid that does half a dozen jobs at once: it cools the bit, carries the crushed rock cuttings back up the outside of the pipe, and, most important, balances the pressure of the fluids in the rock so the well neither collapses nor erupts. When the mud fails at that last job, the result is a blowout, the gusher nobody wanted.

Lining the hole

A drilled hole is not yet a well. As the bit advances, the crew runs casing, steel pipe slightly smaller than the hole, and pumps cement into the gap between pipe and rock, sealing the well from the formations it passes through. The well is drilled in stages, each lined with a narrower string of casing, so a deep well is a telescope of pipes within pipes. Only then is the reservoir section opened, historically with shaped explosive charges called perforating guns, and the oil invited in.

Rows of pumpjacks silhouetted against a setting sun across a wide oilfield.
Pumpjacks at sunset. Where reservoir pressure no longer pushes oil up the well, the nodding donkey lifts it instead. Photo: Arne Huckelheim, CC BY-SA 3.0, via Wikimedia Commons.

Making it flow

The easiest wells flow on their own, pushed up by the pressure of the reservoir. That pressure declines, and most of the world's wells spend most of their lives being lifted: by the pumpjack, the nodding donkey of the oilfield, whose walking beam works a sucker-rod pump at the bottom of the hole, or by electric pumps downhole. When the easy oil is gone, producers squeeze more out: water or gas is injected to sweep oil toward the wells, in the secondary and enhanced recovery the industry has spent decades perfecting.

Steering the bit

For most of the industry's history, wells went more or less straight down. Modern rotary assemblies can be steered, guided by instruments just behind the bit that radio back direction, depth and rock readings while drilling. A modern rig can kick off from vertical, level out horizontal, and then follow a thin reservoir sideways for kilometres, threading the productive layer like a needle. One pad can hold a dozen such wells fanning out beneath the landscape, which is how a small industrial site drains a very large rock formation.

Out of sight of land

The same techniques work from the sea. Fixed platforms stand in the shallows; in deeper water, floating semi-submersibles and drillships hold position over wells kilometres below the seabed, drilling through a riser pipe back to the surface. Offshore drilling costs multiples of the land rig's day rate but reaches provinces no land rig can, from the North Sea to the Gulf of Mexico.

The newest chapter is shale: horizontal wells steered sideways through the source rock itself, then fractured with high-pressure water, sand and chemicals to free oil and gas the rock would never surrender on its own. That technique rewrote the industry's map, the subject of the book's shale chapters.

Quick answers

How does an oil drilling rig work?

A rotary rig turns a bit on the end of a steel drill string, grinding the hole deeper while drilling mud cools the bit, lifts cuttings and controls reservoir pressure. The finished hole is lined with steel casing cemented in place, then perforated and brought into production.

What is a pumpjack for?

A pumpjack lifts oil from wells whose reservoir pressure is no longer strong enough to push oil to the surface. Its walking beam drives a pump at the bottom of the well through a string of sucker rods.

What is fracking?

Hydraulic fracturing pumps water, sand and chemicals at high pressure into a horizontal well to crack the source rock and prop the cracks open, releasing oil or gas the rock would not otherwise yield. It underpins the shale revolution.

Sources

Drilling, casing, lifting and shale technique follow Chapters 12-16 of the book. The U.S. producer ranking is from EIA reporting cited in the book's companion.

More from this book

Geology · From the book Crude Oil: Rock, Fuel, Empire

How crude oil is formed: from plankton to reservoir

Oil is plankton that got buried and slow-cooked by the planet.

History · From the book Crude Oil: Rock, Fuel, Empire

The history of oil drilling: Titusville to Spindletop

For most of history, oil was skimmed from seeps and sold as medicine.

Process · From the book Crude Oil: Rock, Fuel, Empire

How crude oil is refined, from barrel to products

A barrel of crude is a mixture of thousands of hydrocarbons and, as pumped, almost useless.