Cover of Portland Cement: Stone, Fire, Concrete, a book by Ketineni RamaraoFrom the book Portland Cement: Stone, Fire, Concrete
Chapters 14 and 16. Read the full book free as a PDF.
Diagram of typical heat input by kiln type in millions of Btu per ton of cement: wet 5.5, long dry 4.1, preheater 3.5, preheater with precalciner 3.1.
Typical average heat input by kiln type, MMBtu per ton of cement, from the US EPA. Original IOI diagram.

Two ways to feed a kiln

Every rotary kiln is either dry process or wet process. In a wet-process kiln, the raw materials are fed in as a slurry with a moisture content of 30 to 40 percent. The EPA notes that a wet kiln therefore needs extra length compared with a dry kiln just to evaporate the water. In a dry process, the raw materials are ground and fed in as a dry powder. Wet-process kilns tend to be the older operations.

What the water costs

The EPA reports typical average heat input by kiln type, in millions of Btu per ton of cement: 5.5 for a wet kiln, 4.1 for a long dry kiln, 3.5 for a preheater kiln and 3.1 for a preheater and precalciner kiln. It says a wet kiln consumes nearly 33 percent more kiln energy than a dry kiln because of the water in the slurry.

CEMBUREAU, the European cement association, reports the same ordering in different units in a 2018 overview. It puts the best energy efficiency, around 3,300 megajoules per tonne of clinker, as achieved with preheater kilns with precalciners. Long dry kilns without preheater towers use around 33 percent more thermal energy. Old wet kilns use up to 85 percent more than a preheater and precalciner kiln.

The preheater and the precalciner

In preheater and precalciner kilns, the early stages of the process happen before the material enters the rotary kiln. The EPA says these kilns tend to have higher production capacity and better fuel efficiency than other kinds. The American Cement Association describes the preheater tower as using heat generated by the plant to start the reactions, making the kiln firing more efficient. In the precalciner design, the EPA says a calciner vessel sits between the rotary kiln and the preheater.

What does not change

Better kilns cut fuel. They do not remove the carbon in the rock. The EPA separates the two sources of greenhouse gas from a cement kiln: fuel combustion and the calcination reaction that releases CO2 from limestone. The calcination reaction happens whatever the fuel. Fuel is only part of the story: calcination is another large source of the CO2.

Two small dark grey rough spheres of cement clinker, about the size of marbles, sitting on a polished wooden surface.
Two pieces of clinker. Clinker leaves the kiln as grey balls about the size of marbles and is then ground with gypsum to make cement. Photo: Lorenzo Bonino, CC BY 3.0, via Wikimedia Commons.

How fast the old kilns go

Kilns last a long time, usually 30 to 50 years according to CEMBUREAU, so the installed base changes slowly. In the past decade most new plants have been built in Asia, Africa, the Middle East and parts of Eastern Europe, where market growth is expected. A 2018 CEMBUREAU overview says continuous improvements have almost halved European energy use since the 1960s, and that the few remaining older wet kilns will be replaced by modern plants.

Scale matters here. The USGS estimates world cement production at about 3.8 billion tonnes in 2025, with China producing around 1.7 billion and India 470 million. A change in the average kiln across those plants moves more fuel than any single new technology.

Why this matters for the cement you buy

The kiln type does not change the product. The cement that comes out is graded by its chemistry and fineness, as in the types of Portland cement. It changes the energy and carbon cost behind each tonne. For the whole sequence the kiln sits inside, see how Portland cement is made. For the history of the kiln itself, see who invented Portland cement.

Quick answers

What is the difference between wet and dry process cement?

In the wet process the raw materials enter the kiln as a slurry with 30 to 40 percent water. In the dry process they enter as a dry powder, which saves the fuel needed to evaporate the water.

How much more energy does a wet kiln use?

The EPA says nearly 33 percent more than a dry kiln. CEMBUREAU says old wet kilns use up to 85 percent more than a preheater and precalciner kiln.

What is a precalciner?

A vessel between the preheater and the rotary kiln where limestone starts to split into lime and CO2, so the kiln itself does less of the work.

Can a better kiln remove the CO2?

No. It cuts the fuel. The CO2 released when limestone is calcined remains. CEMBUREAU says thermal energy is about 35 percent of the industry's CO2.

Sources

Heat input by kiln type is from the US EPA (typical US averages). The European percentages are from CEMBUREAU and are on a different basis (per tonne of clinker). World production is a USGS estimate rounded to two significant digits.

More from this book

Process · From the book Portland Cement: Stone, Fire, Concrete

How Portland cement is made

Cement is rock that has been cooked until it changes chemistry, then ground back to powder.

Types · From the book Portland Cement: Stone, Fire, Concrete

Types of Portland cement: Type I to V, blended and performance cements

There is no single thing called cement on a construction site.

History · From the book Portland Cement: Stone, Fire, Concrete

Who invented Portland cement? Aspdin, Smeaton and a long argument

The usual answer is Joseph Aspdin, a Leeds bricklayer, in 1824.

Explainer · From the book Portland Cement: Stone, Fire, Concrete

Cement vs concrete: how concrete is made

People say cement when they mean concrete.