Cover of The Jet Engine: Fire in a Tube, and the End of Distance, a book by Ketineni RamaraoFrom the book The Jet Engine: Fire in a Tube, and the End of Distance
Chapters 27 to 31. Read the full book free as a PDF.

Four steps in a tube

Every gas turbine engine, whether it powers an airliner or a fighter, has the same core. NASA Glenn describes the common parts: a compressor, a combustor or burner where fuel is added to high-pressure air and burned, a turbine that the hot gas spins, and a nozzle that produces thrust. The order of the work is the cycle named for the engineer George Brayton.

Diagram of a turbojet in side view, left to right: intake, compressor, combustor, turbine and nozzle, with arrows showing air entering, pressure rising, fuel burning, the turbine driving the compressor through a shaft, and the jet leaving.
The path through a turbojet, intake to nozzle. Original IOI diagram.
  1. Intake and compressor. Air is slowed and squeezed by rows of rotating and fixed blades. Each stage raises the pressure a little. Pressure here is what makes the later burn efficient.
  2. Combustor. Fuel is sprayed into the compressed air and burned continuously. Pressure stays nearly constant while temperature and volume rise.
  3. Turbine. The hot gas expands through turbine blades that drive the compressor and, in a turbofan, the fan, through shafts; many engines use more than one spool. The turbine takes the energy needed to turn them.
  4. Nozzle. What energy remains is converted to speed. The jet leaves faster than the air entered, and the reaction pushes the aircraft forward. NASA Glenn explains that the nozzle also sets the mass flow through the engine.

Why squeeze first

A piston engine burns fuel in a closed cylinder, where pressure and temperature peak together. A gas turbine burns in an open flow. The highest pressure in the machine occurs near the compressor exit, before the burn, in air that is hot from compression but cooler than the combustion gas. The highest temperature occurs after the burn, when the gas is flowing toward the turbine. That separation is a large part of why a continuous-flow engine can make so much power for its weight.

Thrust is momentum

NASA Glenn gives the basic rule: thrust comes from the mass flow of gas leaving the engine multiplied by how much faster it leaves than it arrived, plus a smaller term for pressure at the nozzle exit. More air, or faster air, means more thrust. This is why the engines on airliners have grown wide and why the fan, covered in turbofan vs turbojet engines, mattered so much.

The limits that shape every engine

Two numbers decide how good an engine is. The first is the overall pressure ratio, how hard the compressor squeezes. The second is the temperature of the gas as it first meets the turbine. Higher pressure ratio makes the engine more efficient. Higher temperature makes it more powerful for its size. Both are limited by materials, because the turbine blade sits directly behind the flame. How blade makers meet that limit is the subject of how jet engine turbine blades survive the heat.

NASA Glenn's turbojet page shows the flow temperature colour-coded through a typical engine, blue at the cold intake and white at the hottest point, which sits just after the combustor.

A Rolls-Royce Derwent turbojet cut open and painted so the parts show: orange combustion chambers, a blue-painted air passage, a bladed turbine and a centrifugal compressor.
A cutaway Rolls-Royce Derwent, an early British centrifugal-flow turbojet. The painted sections show where the air runs, where the fuel burns and where the turbine sits. Photo: fw190a8, CC BY-SA 2.0, via Flickr and Wikimedia Commons.

Where the first engines differed

The compressor in Whittle's engine was centrifugal: air was thrown outward by a spinning impeller and gathered in ducts. Many later engines use axial compressors, in which air flows straight through alternating rotor and stator blades. Centrifugal designs are rugged and simple. Axial compressors fit more stages in a narrow body, which gives higher pressure ratios. The cutaway Derwent above is a centrifugal engine, which is why its compressor looks like a wide disc rather than a drum of blades.

The bypass fan

Almost no airliner today uses a pure turbojet. The engines you see under a wing have a large fan on the front driven by the turbine, and most of the thrust comes from air that never enters the core. That change is the subject of turbofan vs turbojet engines.

Quick answers

What are the four main parts of a jet engine?

The compressor, the combustor, the turbine and the nozzle, with an intake in front. Air is compressed, burned with fuel, expanded through a turbine that drives the compressor, and accelerated out of the nozzle.

Why does a jet engine compress the air first?

Compressing air before burning fuel in it makes the burn far more efficient, and in a gas turbine the highest pressure occurs near the compressor exit before combustion, in air that is cooler than the combustion gas.

What does the turbine do in a jet engine?

It extracts energy from the hot gas to turn the compressor, and in a turbofan the fan as well. The rest of the energy goes out of the nozzle as thrust.

Sources

Component roles and the nozzle's role are from NASA Glenn's pages. The statement on what the turbine drives, centrifugal versus axial compressors and the constant-pressure argument follow Chapters 27 to 31 of the book and the standard Brayton-cycle account. No pressure-ratio or temperature figures are quoted, because the sources used here give none.

More from this book

History · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Who invented the jet engine? Whittle, von Ohain and the fire lit twice

Two men who did not know of each other's work, in two countries that would soon be at war, built a working turbojet at the same time.

Engine design · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Turbofan vs turbojet: why airliners moved the thrust to a fan

A turbojet pushes a little air very fast.

Safety · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Why the de Havilland Comet crashed: how metal fatigue changed aircraft design

The Comet was the first jet airliner and a British triumph.

Materials · From the book The Jet Engine: Fire in a Tube, and the End of Distance

How jet engine turbine blades survive heat hotter than their melting point

In a modern jet engine the gas striking the first turbine blades is hotter than the metal would normally survive.