Cover of The Jet Engine: Fire in a Tube, and the End of Distance, a book by Ketineni RamaraoFrom the book The Jet Engine: Fire in a Tube, and the End of Distance
Chapters 30, 69 and 70. Read the full book free as a PDF.

The hottest place in the engine

The turbine sits right behind the combustor, and its blades turn at speed in gas straight from the flame. ASME reports that turbine inlet temperatures in modern high-performance jet engines can exceed 3,000 degrees Fahrenheit (about 1,650 degrees Celsius). It also notes that the nickel-based superalloys used when conventionally cast soften and melt between 2,200 and 2,500 degrees Fahrenheit (roughly 1,200 to 1,370 degrees Celsius). So the gas is hotter than the metal's melting range, and the blade survives by cooling and by structure.

The problem is as old as the engine. Whittle's first engines lost turbine blades repeatedly, because no ordinary steel could hold up. Cambridge University Engineering Department says the fix was Nimonic 60, a high-nickel alloy from Mond Nickel. Every later step in blade metals has been the same idea pushed further.

One crystal instead of many

Ordinary metal is made of many small crystals, called grains. At high temperature and stress, metal creeps, and it does so mostly at the boundaries between grains. If you remove the boundaries you remove the weak path. Pratt & Whitney began a focused programme in the late 1960s to cast whole turbine blades as a single crystal. According to ASME, it took the effort about ten years to go from concept to a production jet engine, a short time by the standards of gas turbine development. Single-crystal blades, ASME reports, can last as much as nine times longer in creep strength and thermal fatigue life than blades with ordinary grain structure.

Two grey metal turbine blades standing on a wooden display base with a label reading P and WA EEE, two-piece single crystal high-pressure turbine blade, and a centimetre scale below.
A pair of single-crystal high-pressure turbine blades from Pratt & Whitney's Energy Efficient Engine programme, shown with a centimetre scale. NASA Glenn photograph, 1979. Photo: Jack Darginsky, NASA Glenn Research Center, Public domain, via NASA and Wikimedia Commons.

The pigtail

The casting trick is a controlled cooling of molten alloy from a chilled plate in a ceramic mould, so crystals grow in one direction. A key part of the process, ASME says, was a helical passage in the mould called a pigtail. Many grains start at the bottom, but the tight twist allows only one to climb through to the blade cavity above.

A brown metal casting shaped like a tall funnel on a stem with a tight corkscrew twist in its middle, standing on a base next to a US half dollar coin for scale.
The "pigtail" selector from a single-crystal blade casting, shown with a Kennedy half dollar for size. The twist lets only one crystal grain grow up into the blade. Photo: Lee Langston, CC BY-SA 4.0, via Wikimedia Commons.

Cooling does the rest

Blades are also hollow, and Princeton's turbine notes confirm that internal cooling lets turbine temperature rise further. Compressor air, which is much cooler than the gas around the blade, is fed through internal passages and out through small holes to cover the surface with a protective film. Coatings add a further layer. The result is that the metal itself runs well below the gas temperature while the engine produces its power.

Why this is where the money is

Blades and other hot-section parts wear out and are replaced, which is why engine makers earn so much after the sale. Aviation Week reports that services provided 63 percent of Rolls-Royce's civil aerospace revenue in 2023, up from about 54 percent a decade earlier. Rolls-Royce says most of its engines are maintained under long-term service agreements in which the airline pays an amount per engine flying hour and the maker maintains the engine to an agreed standard. Under that contract the maker is paid for hours on wing, which gives it a reason to make blades that last.

The single crystal in a blade is therefore both a materials achievement and a commercial one. For the full engine context, see how a jet engine works, and for why bigger fans changed the economics of the aircraft, turbofan vs turbojet.

Quick answers

How do jet engine turbine blades not melt?

They are cast as a single crystal of nickel superalloy, are hollow with internal cooling passages that carry cooler compressor air to the surface, and carry coatings. The metal runs much cooler than the gas around it.

What is a single-crystal turbine blade?

A blade cast so that the whole blade is one metal crystal with no grain boundaries, which gives it much better resistance to creep. ASME says single-crystal blades can last up to nine times longer than conventional ones in creep and thermal fatigue.

Why do jet engine makers make most money after the sale?

Worn hot-section parts must be replaced during overhauls. Rolls-Royce services provided 63 percent of its civil aerospace revenue in 2023, and many engines are sold with long-term service agreements paid per flying hour.

Sources

Turbine inlet temperatures, superalloy melting range, the single-crystal programme history, the nine-times life figure and the pigtail are from the ASME article. The Rolls-Royce services share is from Aviation Week; the service-agreement model is from Rolls-Royce. The description of internal and film cooling is from the book (Chapter 30) and standard references and is stated without figures.

More from this book

History · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Who invented the jet engine? Whittle, von Ohain and the fire lit twice

Two men who did not know of each other's work, in two countries that would soon be at war, built a working turbojet at the same time.

Explainer · From the book The Jet Engine: Fire in a Tube, and the End of Distance

How a jet engine works: compressor, combustor, turbine, nozzle

A jet engine takes in slow air and throws out fast gas.

Engine design · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Turbofan vs turbojet: why airliners moved the thrust to a fan

A turbojet pushes a little air very fast.

Safety · From the book The Jet Engine: Fire in a Tube, and the End of Distance

Why the de Havilland Comet crashed: how metal fatigue changed aircraft design

The Comet was the first jet airliner and a British triumph.