Cover of The Steam Turbine: Heat, Spin, Current, a book by Ketineni RamaraoFrom the book The Steam Turbine: Heat, Spin, Current
Chapters 5, 6 and 8. Read the full book free as a PDF.

The loop around the turbine

A turbine is one part of a cycle. Heat from burning fuel or a nuclear reactor turns water into high-pressure steam in a boiler. The steam goes through the turbine. It then goes to a condenser, where it turns back into liquid water, and a pump sends the water back to the boiler. This is the Rankine cycle, the standard model for a steam power plant. The description here is of a typical condensing power-plant turbine; industrial back-pressure and other arrangements differ.

The condenser is not an afterthought. Condensing the steam drops the pressure at the turbine outlet, so the turbine can extract more work and the feed pump needs only a small fraction of the turbine's output to push the liquid water back to boiler pressure. Pumping liquid is cheap. Compressing steam would not be. That asymmetry is what makes steam power plants work at all.

Two ways to get push from steam

There are two basic types of turbine blading.

According to the Wikipedia reference page on the steam turbine, by 1905, for high-pressure steam, it had become standard to put one or more impulse wheels first, where pressure is highest, followed by reaction stages. That combination reduced steam leakage between rotor and casing at high pressure.

Looking up at three rows of long, tapering steel turbine blades arranged in discs against a clear blue sky.
Rows of low-pressure turbine blades from the Philippsburg nuclear power plant, Germany, now on display at the Technik Museum Speyer (2004). The blades grow longer toward the exhaust because steam expands as it loses pressure. Photo: AlfvanBeem, CC0, via Wikimedia Commons.

Why there are many stages

Except in small machines, the blades are arranged in many stages in series, which is called compounding. A single stage trying to use all the pressure drop would need a rotor speed far beyond what materials can survive. Splitting the drop across many stages keeps the steam speed and the rotor speed manageable. This was Parsons' insight, covered in who invented the steam turbine.

The blades get longer toward the exhaust because steam expands as it loses pressure, so it takes up more volume. The photograph above shows low-pressure blades from a nuclear plant turbine. The last-stage blades of the Arabelle, a very large nuclear turbine, are 75 inches long, according to its maker.

What the efficiency depends on

Real turbines are not ideal. Isentropic efficiency varies widely with machine size and application. The efficiency of the whole plant, though, is set by the temperature and pressure of the steam. Unless a boiler reaches supercritical conditions, the temperature range the cycle works over is fairly small. Supercritical means above 22 megapascals and 374 degrees Celsius, where water stops having separate liquid and steam phases. Most supercritical plants today run at inlet pressures and temperatures well above that. Higher steam conditions mean better efficiency, but they demand better steel, which is why forgings are the bottleneck.

What comes out of the exhaust

In a power plant, condensing turbines exhaust at well below atmospheric pressure, in a partly condensed state. The steam expands a great deal on the way to that low pressure, which is why the exhaust end of the machine is so large. The generator on the same shaft turns the rotation into electricity, which is how a thermal power plant makes electricity. See how much electricity comes from steam-turbine plants.

Quick answers

How does a steam turbine work?

Steam from a boiler is directed over rows of blades on a rotor, which spins. The steam then goes to a condenser and back to the boiler as water. A generator on the same shaft turns the rotation into electricity.

What is the difference between impulse and reaction turbines?

In an impulse turbine, fixed nozzles make fast steam jets that hit the moving blades, and the pressure drops only in the nozzles. In a reaction turbine, the moving blades also act as nozzles, so pressure drops across them too.

Why does a steam turbine have so many stages?

Splitting the pressure drop across many stages keeps the steam and rotor speeds within what materials can survive and improves efficiency. This is called compounding.

Why is there a condenser?

Condensing the exhaust steam lowers the pressure at the turbine outlet so the turbine can extract more work, and pumping the resulting liquid needs only a small fraction of the turbine output.

Sources

Cycle description is from the Rankine cycle reference page. Impulse and reaction, compounding and the 1905 practice are from the Steam turbine reference page. 75-inch blade is a manufacturer figure.

More from this book

History · From the book The Steam Turbine: Heat, Spin, Current

Who invented the steam turbine? Parsons, de Laval and a toy from Roman Egypt

The steam turbine has an inventor for the modern machine and a very long list of earlier tinkerers.

History · From the book The Steam Turbine: Heat, Spin, Current

Turbinia: the ship that proved the steam turbine

Parsons already had working turbines, including at Forth Banks power station, but he still had to prove the marine application.

Economics · From the book The Steam Turbine: Heat, Spin, Current

How much of the world's electricity comes from steam-turbine plants? What the 2024 data shows

No source reviewed gives a single figure for electricity made with steam turbines.

Supply chain · From the book The Steam Turbine: Heat, Spin, Current

Who makes steam turbines, and why heavy forgings have limited supply

A large monoblock steam-turbine rotor shaft is forged from one piece of steel.