Cover of The Submarine Cable, a book by Ketineni RamaraoFrom the book The Submarine Cable
Chapters 22 to 25. Read the full book free as a PDF.

What the cable is made of

KIS-ORCA, the cable-protection organisation, describes the basic deep-water cable as an inner optical core inside a high-tensile steel strength member, clad in a copper power conductor, with polyethylene insulation over it. In water deeper than 2,000 metres it is usually 17 to 21 mm across. The International Cable Protection Committee says that cables like these are similar in size to a garden hose and lie directly on the seabed without armour. Each glass fibre is much smaller than a human hair, and a cable may carry many of them.

Five boxes in a row showing the layers of a modern submarine cable from the centre out: optical fibres, steel strength member, copper conductor, polyethylene insulation and, in shallow water, armour.
The layers of a modern submarine cable. Original IOI diagram.

Armour only where it is needed

In water less than 2,000 metres deep, external steel wire armour inside a polypropylene serving is added against fishing and anchors. The heaviest armoured cable may have a breaking strength above 70 tonnes, and armoured cable may be up to 50 mm across. Strength is not the only limit. Fishing gear can damage the optical path or the insulation at far lower loads by bending the cable below its safe minimum radius, usually 1.5 metres.

Why a cable needs repeaters

The light signal loses strength on the way. KIS-ORCA says repeaters are needed at regular intervals, about 50 to 80 kilometres apart on long cables. Modern repeaters use optical amplification: short lengths of erbium-doped fibre are spliced into the system and energised by lasers, which boosts the incoming light. Shorter cables, such as across the Irish Sea or English Channel, need no repeaters and have amplifiers at either end. A single span of around 240 km is possible without a repeater.

Five boxes showing a signal path: landing station, cable span, repeater, cable span, landing station.
How a signal crosses an ocean cable with repeaters about every 50 to 80 km. Original IOI diagram.

Power from the shore

Each repeater needs electrical power, so long cables are powered, and KIS-ORCA notes that the voltages carried may be very high. The copper conductor is what carries that supply from the landing stations. Damage to or loss of a repeater is serious, and the fix is a repair ship.

Branches

A cable does not have to run from one landing to one other. The ICPC notes that many cable systems serving the Gulf use branching architectures connected to larger trunk systems, which gives the network flexibility and limits the effect of a single fault. TAT-8 itself was built with a branch so that one cable could serve more than one landing.

Landing stations and rerouting

At each end the cable comes ashore at a landing station. Networks are built so that traffic can be rerouted across other cables and over land routes when one cable fails, as the ICPC explains in its enquiries page. In May 2026 the ICPC counted about 500 cable systems and around 1.8 million kilometres of cable worldwide, and its fishing publication says that more than 95 per cent of overseas communications travel by cable rather than satellite.

Where it came from

This design is the end of a long line. TAT-8 in 1988 was the first fibre cable across an ocean, as told in the history of submarine cables. For how the cable gets onto the seabed, see how undersea cables are laid.

Quick answers

How thick is an undersea internet cable?

A deep-water cable is usually 17 to 21 mm across, about the size of a garden hose. Armoured shallow-water cable can be up to 50 mm.

How does the signal travel across the ocean?

As light through hair-thin glass fibres. Repeaters about every 50 to 80 km amplify it, powered through the cable's copper conductor from shore.

Do all undersea cables need repeaters?

No. Short cables such as across the Irish Sea or English Channel have none, and a single span of around 240 km is possible without a repeater.

Sources

Cable structure, diameters, armour, repeater spacing and power feed are from KIS-ORCA. The garden hose comparison and unarmoured deep-water cable are from the ICPC. The 95 per cent figure is the ICPC fishing booklet (2009 second edition); other bodies quote different shares, so treat it as an approximate floor. Network totals are from the ICPC enquiries page. The diagram shows the generic layer order described by KIS-ORCA, and individual cable designs vary.

More from this book

History · From the book The Submarine Cable

The first submarine cable: Dover to Calais, 1850

The first international submarine cable was a bare copper wire coated in tree sap.

History · From the book The Submarine Cable

The history of submarine cables, from telegraph to fibre

Submarine cables have been rebuilt around their failures.

Explainer · From the book The Submarine Cable

How undersea cables are laid

Laying an undersea cable starts years before the ship sails.

Explainer · From the book The Submarine Cable

Why undersea cables break

Undersea cables break all the time, and mostly by accident.